You can sand back the stained wood to a lighter grade. You can fine-tune the grade of staining by the quantity of dye you apply to the wood. When using stain take care that the solvent/water of the stain fits with the later finish, otherwise the result may be "bloody" due to bleeding of the stain when the solvent of the lacquer is solving the stain (again). With stain or dye you can deeply enhance the figure of the wood, esp. We carry this, check out the "Various" section at the left and scroll down to this item for learning more about this. This stuff works excellent as a grain filler under shellac, too. Always check if the type of stain or dye fits with the finish/lacquer, otherwise the base may "blood" (bleeching).Īpart from the above mentioned traditional grain filling method, that is bases on solids, recently a quite new method came up, suggested by luthier Tim McKnight: Z-Poxy resin for pore filling. when trying to get a Les Paul-like cherry red finish with dark mahogany pores. If not come back to us and ask, we are always glad to help in cases of emergency.ĭepending on the visual effect you are going for sometimes it is good to mix stain with the grain filler, i.e. Such stuff is widely available at most woodworker stores and not worth to offer here, we are sure your local woodworking shop can help at low costs. Yes we can - going back to the woods: porous woods like Mahogany, Rosewoods, Koa and several others need a grain fill befor applying the Vinyl Sealer (above).įor this you can use any grain filler that is suitable for NC lacquers. NOTE: Vinyl Sealer may be applied over raw wood or filled and stained substrates. Vinyl Sealer is offered in a ready to use formulation that needs no further reduction or a catalyst. Vinyl Sealer develops an excellent moisture barrier for the wood substrate, while providing a good base for all Behlen lacquer finishes. We go backwards: you may have read above that the Stringed Instrument Lacquer should be used over a Vinyl Sealer. If you are interested in using aerosol for finishing guitars check out Behlen´s Finishing Instructions using aerosol cans. View the Material Safety Data Sheet PDF for this product. Note: Stringed Instrument Lacquer must be applied over Behlen Vinyl Sealer in order to insure its unique film building and special finish characteristics. Stringed Instrument Lacquer allows for the special expansion and contraction that can occur due to the unique construction of stringed instruments. Stringed Instrument Lacquer is a high quality nitrocellulose lacquer specifically designed for wooden stringed instruments. Available from us in cans and in aerosols. This is Behlen´s nitrocellulose lacquer that was specially designed for the needs when finishing an acoustic (stinged) musical instrument. This video seems to us not as a very good marketing idea from Behlen, but for some this might be useful so we offer it for viewing - click here(wmv-format, this is a excerpt from an instruction DVD). We carry the following Behlen-products that were designed specially for guitars and other stringed musical instruments.īehlen is the only company that offeres guitar lacquers even in aerosol cans, a handy and good advantage for the amateur luthier or professional repair job/touch up. Right venue for everyone who does not want to set up a HVLP-spraying system but wants not to miss the advantages of special musical instrument NC lacquer.īelow you can find a general finishing schedule for finishing a guitar with Behlen Stringed Instrument NC Lacquer as well as Behlen´s color chart -> click on the pic for a full size version:įor a - in our opinion quite bad - trailer about spraying a guitar using aerosols click on the following link. We know of only 2 manufactors of suitable NC lacquer for discriminating needs of luthiers of stringed instruments worldwide, one of them is the traditional company "Behlen". While for (colored) electric guitars amateur luthier often use several car finishing aerosols - here colored NC lacquer is widely available -, it is quite hard to find a (gloss) nitrocellulose lacquer that is suitable for stringed instruments. Known as the best or most resonant finish for acoustic guitar is thin nitrocellulose lacquer or - mainly used for classical guitars - a shellac finish. When all woodwork is done the next task before stringing up is on the way: Wear a mask and enter the FINISHING DEPT.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |